Avast 19.5

[bob3160]

I saw a notice on the Avast sys. tray that there was a program update.
Since it's not posted on the forum, you can update from within the User Interface or
get the downloads from here: https://goo.gl/4Ptzkf

[bob3160]

https://forum.avast.com/index.php?topic=93544.msg1506370#msg1506370

[Be Secure]

It is very unusual that avast not give stable version official changelog on forum. ???Got the notice and update via GUI...

Edit:My Smart scan UI not changed.It still use Old UI with no info.

[DavidR]

Have you rebooted it after the update ?

If you have I believe there have been a couple reporting it needing to be rebooted twice.  I'm in no rush.

[Be Secure]

Have you rebooted it after the update ?

If you have I believe there have been a couple reporting it needing to be rebooted twice.  I'm in no rush.

No.Only single reboot done but going to do that ASAP

Edit:No solved.

[jefferson sant]

Is an official version, the release day is marked as 9 April 2019, if we are in the month of May, what will be shown is the date current ?

I stay old version from here or expect to update later ?

[Be Secure]

Is an official version, the release day is marked as 9 April 2019, if we are in the month of May, what will be shown is the date current ?

I stay old version from here or expect to update later ?

You should update to new.
It was earlier version release day(19.4)
My avast 20th may/2019(19.5)

[jefferson sant]

You should update to new.
It was earlier version release day(19.4)
My avast 20th may/2019(19.5)

an error in the current interface UI ?

Always before updating, we were informed of the release date of the update.

Open Avast-> General -> Troubleshooting-> Open old settings.

The message is display correctly

[Be Secure]

You should update to new.
It was earlier version release day(19.4)
My avast 20th may/2019(19.5)

an error in the current interface UI ?

Always before updating, we were informed of the release date of the update.

Open Avast-> General -> Troubleshooting-> Open old settings.

The message is display correctly

Maybe...

[DavidR]

You should update to new.
It was earlier version release day(19.4)
My avast 20th may/2019(19.5)

an error in the current interface UI ?

Always before updating, we were informed of the release date of the update.

Open Avast-> General -> Troubleshooting-> Open old settings.

The message is display correctly

You could try an Avast Repair.  This used to resolve what I call and out of sync condition. e.g. where what is reported differs from the physical state.

[abruptum]

Avast! 19.5.2378

Free

  https://files.avast.com/iavs9x/avast_free_antivirus_setup_offline.exe


Pro

  https://files.avast.com/iavs9x/avast_pro_antivirus_setup_offline.exe


Internet Security

  https://files.avast.com/iavs9x/avast_internet_security_setup_offline.exe


Premier

  https://files.avast.com/iavs9x/avast_premier_antivirus_setup_offline.exe

[reddyshyam]

It is very unusual that avast not give stable version official changelog on forum. ???Got the notice and update via GUI...

Edit:My Smart scan UI not changed.It still use Old UI with no info.

Mine as well. We were told at launch of 19.4, it was being set geographically to avoid burnout but even after a month down the line and a version upgrade i.e. 19.5, smart scan UI remains old.

And yes, I have rebooted more than 4 times just in case anyone asks.

[slavo.benko]

Here is the proper topic, excuse the small delay.
 https://forum.avast.com/index.php?topic=227342.0

[YeOldeBowler]

After updating to 19.5 through the UI I had to reboot twice. The smart scan was not working correctly (it did not increment the percentage and stopped after a while). I tried to stop the scan but that did not work. I closed the UI and started the UI again from the systray and it stated that the scan was completed. I then ran smart scan again and the same happened.
I then did a repair from control panel and all seems to be okay now. Will try a smart scan again later to ensure all is well.

[jefferson sant]

You could try an Avast Repair.  This used to resolve what I call and out of sync condition. e.g. where what is reported differs from the physical state.

Repair did not change status of message.I think they tried to modify since new UI introduced which was not a good idea.I decided to update now.